How to Install TubShroom Toss Disposable Drain Covers: Step-by-Step Guide for Shower and Sink Drains

Disposable drain covers offer a convenient, no-clean alternative to reusable hair catchers. The TubShroom Toss 21pk provides mesh stickers that trap hair before it reaches the drain, preventing clogs without the need to rinse or scrub. Whether you use them in the shower, bathtub, or bathroom sink, proper installation is key to keeping the cover in place and the water flowing.

In this guide, we’ll walk you through the exact steps for setting up a TubShroom Toss disposable drain cover. You’ll learn how to prepare the drain, apply the sticker, and ensure a tight seal that stays put during showers and sink use. We’ll also cover common mistakes to avoid so you get the most out of each cover.

What You’ll Need Before You Start

Before installing a disposable drain cover, gather a few basic supplies: a clean, dry drain surface, a TubShroom Toss 21pk (or similar disposable mesh sticker), and a soft cloth or paper towel. No tools or adhesives are required—the covers come with a pre-applied adhesive backing. Make sure the drain area is free of standing water, hair, and soap residue. A clean surface helps the sticker bond firmly.

If you’re applying the cover to a sink drain, consider pairing it with a reusable protector like the SinkShroom Ultra for double protection. For bathtubs, the TubShroom (Orange) reusable catcher works well alongside disposables for high-traffic households. But if you prefer a quick, single-use solution, the TubShroom Toss is all you need.

• Tip: For best adhesion, apply the cover at least 30 minutes before the first use, especially in humid bathrooms.

Step-by-Step Installation for Shower and Bathtub Drains

Start by removing the existing drain cover or strainer if present. Wipe the drain opening and the surrounding area with a dry cloth to remove moisture and debris. Peel the backing off the TubShroom Toss disposable cover, exposing the adhesive side. Center the mesh over the drain opening, ensuring the adhesive ring sits flat on the surrounding surface. Press firmly around the entire edge for 10–15 seconds.

For bathtub drains, the flat surface around the drain is usually smooth and level, making adhesion straightforward. If your tub has a slightly raised rim, press the sticker down gradually from the center outward to avoid air bubbles. The mesh should lie flat without wrinkles—wrinkles can create gaps where hair might slip through. Once applied, run a small amount of water to test the seal. If water pools under the sticker, lift and reapply with more pressure.

• Avoid stretching the mesh during application; it should sit naturally over the drain.
• If the drain is wet, use a hair dryer on low heat to dry the area completely before applying.

How to Install on a Bathroom Sink Drain

Bathroom sink drains are smaller and often have a pop-up stopper or a metal grid. Remove the stopper or lift the grid if possible. Clean the drain rim with a dry cloth and let it air-dry for a minute. Peel the TubShroom Toss cover and align it so the mesh covers the drain hole completely. The adhesive ring should stick to the flat rim of the sink drain, not the interior.

Because sink drains are recessed, the sticker may need to conform to a slight curve. Press firmly with your fingertips, working around the circle. Avoid covering the overflow opening if your sink has one—the cover is designed only for the main drain. For sinks with a pop-up stopper, you can either remove the stopper permanently or apply the cover over the closed stopper. The latter works well if you rarely use the stopper. For a more permanent solution, consider the SinkShroom (Nickel Edition) as an alternative.

• If the sink drain rim is textured or grooved, press the adhesive extra firmly to ensure a seal.

How Long Does a TubShroom Toss Cover Last?

Each TubShroom Toss cover is designed for single use, typically lasting one to two showers or sink sessions depending on hair volume. When the mesh becomes full of hair or water starts to pool around the drain, it’s time to replace it. Simply peel off the old cover, clean the drain area, and apply a new one. The 21-pack provides a three-week supply for most households.

If you notice the adhesive weakening before the cover is full, check for moisture or soap residue on the drain surface. Applying the cover to a completely dry surface and avoiding direct spray from the showerhead can extend its life. For heavy-use bathrooms, you might alternate between a reusable catcher like the TubShroom (Orange) and disposables to reduce waste while maintaining protection.

• Store unused covers in a cool, dry place to prevent the adhesive from degrading.

Common Mistakes and How to Avoid Them

The most common mistake is applying the cover to a wet or soapy drain. Even a thin film of moisture can prevent the adhesive from bonding, causing the sticker to lift during use. Always dry the drain thoroughly with a cloth and let it sit for a minute. Another issue is misalignment—if the mesh doesn’t fully cover the drain opening, hair can bypass the cover. Center the sticker carefully before pressing down.

Some users try to reuse a cover by rinsing it off. While the mesh may still catch hair, the adhesive loses grip after the first removal, leading to leaks. Stick to single use for reliable performance. If you’re in a shared bathroom, label the pack or set a replacement schedule to avoid confusion. For sinks with a stopper, remember to remove the stopper before applying the cover, or use the cover over the closed stopper for a simpler setup.

• If the cover lifts at the edges, apply a small piece of clear tape over the corner as a temporary fix.

Installing a TubShroom Toss disposable drain cover takes less than a minute once you know the steps. A clean, dry surface and firm pressure are all it takes to keep hair out of your pipes. Whether you use them in the shower, bathtub, or bathroom sink, these mesh stickers offer a mess-free way to prevent clogs. Replace them as needed, and your drains will stay clear with minimal effort.